{"created":"2023-05-15T14:37:19.858363+00:00","id":48137,"links":{},"metadata":{"_buckets":{"deposit":"d8bbcb54-d187-4345-a0e2-4aeb22f32b14"},"_deposit":{"created_by":1,"id":"48137","owners":[1],"pid":{"revision_id":0,"type":"depid","value":"48137"},"status":"published"},"_oai":{"id":"oai:repo.qst.go.jp:00048137","sets":["1"]},"author_link":["483374","483381","483384","483377","483382","483372","483375","483379","483383","483376","483380","483378","483385","483373"],"item_8_biblio_info_7":{"attribute_name":"書誌情報","attribute_value_mlt":[{"bibliographicIssueDates":{"bibliographicIssueDate":"2017-06","bibliographicIssueDateType":"Issued"},"bibliographicIssueNumber":"4","bibliographicPageStart":"6001004","bibliographicVolumeNumber":"26","bibliographic_titles":[{"bibliographic_title":"IEEE TRANSACTIONS ON APPLIED SUPERCONDUCTIVITY"}]}]},"item_8_description_5":{"attribute_name":"抄録","attribute_value_mlt":[{"subitem_description":"Nb–Ti conductors will be used for equilibrium field (EF) coils and the feeder of JT-60 Super Advanced (JT-60SA). The conductors were fabricated by pull through and compaction method. Round jackets were butt welded to a long length jacket.\nThen, the cable was pulled into the jacket. Finally, the conductor was formed into a square shape. Sixty-four conductors were produced. Dimensional measurements at both ends of 2183 jackets showed that the inner diameters of each production series were within ±0.1 mm. There were 2175 welding joints in total. Cut and rewelding, according to the failure detected by inspections, occurred 30 times. The maximum pulling forces through a jacket was 8.3 kN. The range of coefficients of friction for pulling was from 0.50 to 0.86. The outer dimension just after compaction\nsatisfied the specification of ±0.2 mm in tolerance. The height of the conductor was increased by 0.19 mm in average by bending of 1.5 m in curvature radius. This modification did not affect the coil manufacturing. The minimum mass flow rate among the same EF coil’s conductors was 93.5% of the average value. It was decided that orifices to uniform helium parallel flows inside coil are not used for coil manufacturing.","subitem_description_type":"Abstract"}]},"item_8_publisher_8":{"attribute_name":"出版者","attribute_value_mlt":[{"subitem_publisher":"IEEE"}]},"item_8_relation_14":{"attribute_name":"DOI","attribute_value_mlt":[{"subitem_relation_type_id":{"subitem_relation_type_id_text":"10.1109/TASC.2016.2537142","subitem_relation_type_select":"DOI"}}]},"item_8_source_id_9":{"attribute_name":"ISSN","attribute_value_mlt":[{"subitem_source_identifier":"1051-8223","subitem_source_identifier_type":"ISSN"}]},"item_access_right":{"attribute_name":"アクセス権","attribute_value_mlt":[{"subitem_access_right":"metadata only access","subitem_access_right_uri":"http://purl.org/coar/access_right/c_14cb"}]},"item_creator":{"attribute_name":"著者","attribute_type":"creator","attribute_value_mlt":[{"creatorNames":[{"creatorName":"木津, 要"}],"nameIdentifiers":[{"nameIdentifier":"483372","nameIdentifierScheme":"WEKO"}]},{"creatorNames":[{"creatorName":"土屋, 勝彦"}],"nameIdentifiers":[{"nameIdentifier":"483373","nameIdentifierScheme":"WEKO"}]},{"creatorNames":[{"creatorName":"村上, 陽之"}],"nameIdentifiers":[{"nameIdentifier":"483374","nameIdentifierScheme":"WEKO"}]},{"creatorNames":[{"creatorName":"柏, 好敏"}],"nameIdentifiers":[{"nameIdentifier":"483375","nameIdentifierScheme":"WEKO"}]},{"creatorNames":[{"creatorName":"夏目, 恭平"}],"nameIdentifiers":[{"nameIdentifier":"483376","nameIdentifierScheme":"WEKO"}]},{"creatorNames":[{"creatorName":"小出, 芳彦"}],"nameIdentifiers":[{"nameIdentifier":"483377","nameIdentifierScheme":"WEKO"}]},{"creatorNames":[{"creatorName":"吉田, 清"}],"nameIdentifiers":[{"nameIdentifier":"483378","nameIdentifierScheme":"WEKO"}]},{"creatorNames":[{"creatorName":"木津 要","creatorNameLang":"en"}],"nameIdentifiers":[{"nameIdentifier":"483379","nameIdentifierScheme":"WEKO"}]},{"creatorNames":[{"creatorName":"土屋 勝彦","creatorNameLang":"en"}],"nameIdentifiers":[{"nameIdentifier":"483380","nameIdentifierScheme":"WEKO"}]},{"creatorNames":[{"creatorName":"村上 陽之","creatorNameLang":"en"}],"nameIdentifiers":[{"nameIdentifier":"483381","nameIdentifierScheme":"WEKO"}]},{"creatorNames":[{"creatorName":"柏 好敏","creatorNameLang":"en"}],"nameIdentifiers":[{"nameIdentifier":"483382","nameIdentifierScheme":"WEKO"}]},{"creatorNames":[{"creatorName":"夏目 恭平","creatorNameLang":"en"}],"nameIdentifiers":[{"nameIdentifier":"483383","nameIdentifierScheme":"WEKO"}]},{"creatorNames":[{"creatorName":"小出 芳彦","creatorNameLang":"en"}],"nameIdentifiers":[{"nameIdentifier":"483384","nameIdentifierScheme":"WEKO"}]},{"creatorNames":[{"creatorName":"吉田 清","creatorNameLang":"en"}],"nameIdentifiers":[{"nameIdentifier":"483385","nameIdentifierScheme":"WEKO"}]}]},"item_language":{"attribute_name":"言語","attribute_value_mlt":[{"subitem_language":"eng"}]},"item_resource_type":{"attribute_name":"資源タイプ","attribute_value_mlt":[{"resourcetype":"journal article","resourceuri":"http://purl.org/coar/resource_type/c_6501"}]},"item_title":"Mass production of Nb-Ti conductors for EF coil and feeder of JT-60SA","item_titles":{"attribute_name":"タイトル","attribute_value_mlt":[{"subitem_title":"Mass production of Nb-Ti conductors for EF coil and feeder of JT-60SA"}]},"item_type_id":"8","owner":"1","path":["1"],"pubdate":{"attribute_name":"公開日","attribute_value":"2017-07-20"},"publish_date":"2017-07-20","publish_status":"0","recid":"48137","relation_version_is_last":true,"title":["Mass production of Nb-Ti conductors for EF coil and feeder of JT-60SA"],"weko_creator_id":"1","weko_shared_id":-1},"updated":"2023-05-15T23:31:31.645987+00:00"}